Clubhouse manual

How to attach your patch

A good patch should look like it has always belonged there. Choose the method for the fabric—not just the fastest route—and take your time around heat, curves, and stretch.

Check the garment care label first. If your patch arrives with backing-specific instructions, those instructions take the lead.

01 • IRON-ON

Fast, flat, and clean

Use this only with a heat-activated backing and a fabric that can safely take the temperature. It is best on sturdy, smooth cotton, denim, twill, and canvas.

Cotton / denim325–350°F (163–177°C), 20–30 seconds

Poly blends275–300°F (135–149°C), 10–15 seconds; test first

  1. Prep the fabric. Wash and dry it without fabric softener. Work on a firm, heat-safe surface—not a padded ironing board.
  2. Set the iron. Turn steam off and empty the water. Let the iron reach the correct temperature for the garment.
  3. Place and protect. Put the adhesive side against the fabric. Cover the patch with a thin cotton pressing cloth.
  4. Press—do not slide. Apply firm, even pressure for the time above. For a large patch, work section by section without shifting it.
  5. Press from the back. Turn the garment inside out and press behind the patch for another 10–15 seconds, if the care label allows.
  6. Let it cool. Leave it flat and untouched until fully cool. Check the edge; if it lifts, repeat in short 5-second presses.

NEVER USE STEAM • NEVER PRESS DIRECTLY ON THE PATCH FACE • LET THE ADHESIVE SET A FULL 24 HOURS BEFORE WASHING

02 • SEW-ON

The road-game hold

Sewing is the dependable choice for jackets, bags, hats, workwear, stretch fabrics, and anything that will see frequent wear or washing.

  1. Choose the spot. Put the garment on first if placement matters. Mark the center, then lay the item flat.
  2. Hold it still. Use a few pins or removable fabric tape. Keep the patch flat without stretching the garment beneath it.
  3. Match the border. Use strong polyester thread close to the outer edge color and a needle suited to the fabric weight.
  4. Start inside. Knot the thread on the garment’s reverse so the tail stays hidden.
  5. Work the perimeter. Make small, even whipstitches about ⅛ inch (3 mm) apart, catching the patch border without crossing the artwork.
  6. Finish cleanly. Overlap the first few stitches, knot securely on the reverse, and trim the thread. Check the edge all the way around.

FOR EXTRA SECURITY: IRON ON FIRST, THEN ADD A FEW STITCHES AROUND THE BORDER

Match the method to the material

When the garment label says “do not iron,” believe it. Sewing takes longer, but it avoids melted coatings, shine marks, and warped stretch fabric.

Denim, cotton twill, canvasIRON-ON OR SEW-ONExcellent heat tolerance. Sew the edge as well for jeans, jackets, and bags that get hard use.
Cotton tees and sweatshirtsSEW-ON PREFERREDIron-on can work, but knit fabric flexes while the patch does not. A few stitches help prevent lifting and puckering.
Polyester and blendsLOW-HEAT TEST OR SEWTest a hidden area first. Stop if the fabric shines, ripples, or changes color. Sewing is the safer call.
Nylon, rain shells, waterproof gearSEW-ONHeat can melt the cloth or damage its coating. Seal needle holes if the item must stay waterproof.
Wool and feltHAND-SEWGentle hand-stitching protects the loft and avoids a pressed, shiny patch around the placement.
Leather, faux leather, vinylPROFESSIONAL SEWINGSkip the household iron. Needle holes are permanent, so use a leather needle or ask a tailor or leather shop.
Hats and curved panelsHAND-SEWCurves rarely receive even iron pressure. Shape the patch to the panel and stitch slowly around the border.
Spandex, performance knits, delicatesAVOID OR HAND-SEWThe patch will not stretch with the fabric. If you proceed, use fine hand stitches in a low-stretch area.
AFTER THE FINAL OUT

Care and washing

Cooler water, gentler cycles, and less friction keep the border sharp and the colors in the game.

  • BEFORE THE FIRST WASHLet the adhesive set a full 24 hours before the first wash.
  • TURN IT INSIDE OUTProtect the patch face from zippers, buttons, and the washer drum.
  • WASH COLDUse a gentle cycle and mild detergent. Skip bleach and fabric softener.
  • AIR-DRY WHEN POSSIBLEHigh dryer heat can weaken adhesive and distort the patch or garment.
  • IRON FROM THE REVERSEUse a pressing cloth and low heat. Never put the iron directly on the patch face.
  • CHECK THE EDGEIf an iron-on corner lifts, re-press it. If it keeps lifting, secure the border with a few stitches.

Ready to choose the patch that gets the spot?

Back to the patch archive